![]() ![]() ![]() ![]() It is therefore desirable to use beacons with longer battery life.īeacons are small battery powered devices. The backend cloud server processes the information and performs further analysis guiding specific location based behaviors in the mobile device.īeacons consist of four primary components which we detail below: The signal is picked up by the phone, and often transmitted to a cloud server via the internet. The hardware consists of a microcontroller with a Bluetooth LE radio chip and a battery. New radio chips are optimized for Bluetooth LE, whereas older versions were designed for Bluetooth Classic which had higher power consumption. The radio chip is commonly manufactured by two major companies: 1) Texas Instruments and 2) Nordic Semiconductor. Companies such as BlueGiga and Gimbal use the underlying hardware from Texas Instruments (TI) but with their custom firmware before selling them to beacon vendors.Ĭoin cell batteries are the most popular choice for most beacons. These batteries are dense Lithium Ion cells and provide up-to 1,000 mAh of stored power in a very small form factor. Coin cell batteries are otherwise commonly used in key fobs and digital watches.Ĭommonly available coin cell sizes are 240 mAh (CR2032, small size), 620 mAh (CR2450, medium size) and 1,000 mAh (CR2477, large size). Some beacons also use Alkaline AA batteries, which are commonly used in digital cameras and TV remotes. A typical AA battery provides around 2,000 mAh power but at a significantly larger size than coin cell batteries. In order to re-enter normal operational model, simply remove and replace power to the device.Lastly, some beacons are externally powered. Reboot the beacon into Direct Firmware Update mode.Ĭontact Radius Networks support for information on the procedure for firmware update or replacement. Press the Action Menu button and select DFU. In order to re-enter configurable mode for a RadBeacon X2, remove the front cover and switch the beacon power switch to OFF and back to ON.Ī beacon set in configurable mode will be configurable for up to 30 minutes or until you lock the device again. In order to re-enter configurable mode for a RadBeacon Tag, remove the front cover and press the configuration push button switch near the coin cell battery. In order to re-enter configurable mode for a RadBeacon USB, remove and restore power to the device. The Lock feature is a security precaution to limit the possibility of third party manipulation of your beacons once they have been installed and configured. Submit a valid PIN to prevent connections from remote Bluetooth 4.0 devices to the beacon configuration service. Press the Action Menu button and select Lock. Submit a valid PIN to reset the settings for your beacon to factory defaults. Reset the device to the original factory settings. Press the Action Menu button and select Reset. Submit a new and existing PIN to update the PIN for your beacon. Press the Action Menu button and select Update PIN. Validate the accuracy of your beacon settings by quickly verifying the ranging behavior of your device in proximity to your configured beacon. Press the Action Menu button and select Range. Update the measured power value with the results of your calibration activity and update your settings. Press the Action Menu button and select Calibrate.Ĭalibrate the measured power value of the beacon settings to ensure optimal proximity events and ranging. Submit a valid PIN to update the settings for this beacon. (If the RadBeacon is not configurable, then an "unable to connect" message will be displayed after approximately 15 seconds.) The settings displayed include: If the RadBeacon is configurable, its detailed settings will be displayed. Each beacon discovered is displayed with the following summary details Scan for nearby configurable RadBeacons by pressing the SCAN button. Once discovered, if the beacon is configurable, you can display each beacon's operating settings and make modifications to those settings. With the RadBeacon app you can scan for nearby Radius Networks beacons. The RadBeacon app from Radius Networks requires an Android device running Android 4.3 or higher and equipped with Bluetooth 4.0 capabilities. The RadBeacon™ app is the configuration utility for RadBeacon proximity beacons from Radius Networks that support Apple's iBeacon™ proximity services and the AltBeacon proximity services for Android devices. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |